New pool wiring
Feeder, subpanel, pump, filter, heater and light circuits for in-ground and above-ground pools.
Pool, spa & hot tub electrical
Pool and Hot Tub Wiring in Marlboro, NJ with Same-Day Service Calls
Water and electricity call for the strictest rules in the electrical code. Whether you're adding an in-ground pool, setting a new hot tub on the patio or fixing a pump that keeps tripping, our licensed electricians wire it safely and to code. If you're searching for a pool electrician near me, we serve Marlboro, Colts Neck, Manalapan and nearby towns.
Pump down in July? We offer same-day service calls, and our emergency line is open 24 hours.
- Bonding to code
- GFCI protection
- Spa disconnects
- Pump & heater circuits
Full pool electrical
Pool and Spa Electrical Work We Handle
From the panel to the pump pad, we handle every electrical part of your backyard water project.
Equipotential bonding
The copper grid that keeps the pool, deck and metal parts at the same voltage.
Hot tubs and spas
Dedicated 240 volt circuits with a GFCI spa disconnect placed to code.
Pumps and heaters
Variable speed pumps, gas heater controls and electric heat pumps.
Pool and deck lighting
Low-voltage pool lights, deck lights and landscape lighting around the water.
Timers and controls
Pump timers and automation so equipment runs on schedule.
Safety first
Why Pool Bonding and GFCI Protection Matter
These two protections are what make it safe to swim.
Equipotential bonding
Bonding connects the pool shell, reinforcing steel, deck, ladders, rails, pump motor and nearby metal with solid copper. It keeps everything at the same voltage so no one in or near the water can become a path for current.
Bonding has to be done before the deck is poured or pavers go down, and it's inspected at that stage. Plan for it early with your pool builder.
GFCI protection
The 2020 National Electrical Code, which New Jersey enforces, requires GFCI protection for pool pump motors and for outlets near pools. A GFCI cuts power in a fraction of a second if current leaks where it shouldn't.
- Pump, filter and heater circuits
- Outlets near the pool and hot tub
- Pool lights, where required
- Test GFCIs monthly during swim season
Hot tub hookups
Hot Tub and Spa Electrical Hookups
Order the tub, then call us. We'll have the power ready on delivery day.
Most full-size hot tubs need a dedicated 240 volt circuit, often 40 or 50 amps, plus a GFCI spa disconnect. The disconnect must be within sight of the tub and kept a safe distance from the water, so you can shut it off without reaching over the spa.
What we check first
- Your panel's capacity for a large new load
- The manufacturer's amp and wire size requirements
- A clear path for the cable from panel to patio
- Overhead wires and clearances above the tub
If your panel is already near its limit, we'll talk about an electrical panel upgrade before the tub arrives. Plug-and-play 120 volt spas may only need a properly placed GFCI outlet.
Troubleshooting
Pool Pump Keeps Tripping? Common Causes
A pump that trips its GFCI is telling you something. Don't just keep resetting it.
| What happens | Likely cause |
|---|---|
| GFCI trips when the pump starts | Moisture in the motor or wiring, a failing motor, or a worn GFCI |
| Breaker trips after running a while | An overloaded or failing motor, or a loose connection |
| Pump hums but won't spin | A failed start capacitor or seized motor |
| Pool light won't turn on | A tripped GFCI, a failed bulb or water in the light niche |
| Timer doesn't start the pump | A failed timer mechanism or wiring issue at the timer box |
We repair the electrical side and work with your pool company on the equipment side. For general troubleshooting in the house, see electrical repair.
New pool projects
How We Work With Your Pool Builder
Plan with the builder
We confirm equipment, loads and the pad location with your pool company.
Permit
We file the electrical permit with the Marlboro Construction Division.
Bonding and rough-in
We install bonding before the deck is poured and run underground feeders.
Equipment hookup
Pumps, heater, lights, timers and the subpanel are wired and tested.
Final inspection
The inspector signs off, and you're ready to open the pool.
Helpful guides
Read Before You Book
Plain-English answers to the questions homeowners ask us most.
Brands & service areas
Brands We Service and Towns We Cover
Brands We Work With
Pool timers and the subpanels and breakers that power your pool equipment.
View All BrandsServing Marlboro and Nearby Towns
Pool and hot tub wiring in Marlboro and these nearby towns.
View All Service AreasQuestions
Frequently Asked Questions
What size circuit does a hot tub need?
Most full-size hot tubs need a dedicated 240 volt circuit, often 40 or 50 amps. Your tub's manual lists the exact size. Smaller plug-in spas use a 120 volt GFCI outlet.
What is pool bonding?
Bonding connects all metal parts of the pool, deck and equipment with copper so they stay at the same voltage. It prevents dangerous voltage differences around the water.
Why does my pool pump keep tripping the GFCI?
Common causes are moisture in the motor or wiring, a failing motor, or a worn GFCI. We test to find the cause.
Do I need a permit for pool or hot tub wiring in New Jersey?
Yes. Pool and spa wiring needs an electrical permit and inspections, including a bonding inspection before the deck is poured.
Where does the hot tub disconnect go?
Within sight of the tub and a safe distance from the water, as the code requires. We place it where it's easy to reach and compliant.
Can you add lighting around my pool?
Yes. We install low-voltage pool lights and deck and landscape lighting placed to code around the water.
Get Your Pool or Hot Tub Powered Safely
Book a visit with a licensed Marlboro electrician for pool wiring, hot tub hookups and pump repairs.
(732) 419-5195